Product Description

                                                                                    Stainless Steel Tube Fitting Tee
Product Description:

1.Available in size: 1/16″ to 1″, and 2mm to 25mm.

2.Working temperature:-325ºF~800ºF (-198ºC~426ºC).

3.Material grades: SS 304, SS 316, Brass, Special Alloys.

4.Thread:NPT, BSP, BSPT, UNF, ISO, SAE etc.

5.Zero leakage even under tough working conditions.

6.High quality silver plated threads on nuts to ensure no galling on the body threads.

7.Simple to operate and save time and cost because of the usage of elastic seal.

8.Available in wide variety of configurations.

9.It can be reused.

 

-SK3 Union Tee (Inch Tube OD x Inch Tube OD x Inch Tube OD)
Ordering Number	A		D	W		E
	in	mm	mm	in	mm	mm
-SK3-1	1/16	1.58	1.27	3/8	9.52	17.80
-SK3-2	1/8	3.17	2.28	1/2	12.70	22.35
-SK3-3	3/16	4.76	3.04	1/2	12.70	24.40
-SK3-4	1/4	6.35	4.82	1/2	12.70	26.92
-SK3-5	5/16	7.93	6.35	5/8	15.87	29.71
-SK3-6	3/8	9.52	7.11	5/8	15.87	30.48
-SK3-8	1/2	12.70	10.41	13/16	20.63	36.10
-SK3-10	5/8	15.87	12.70	15/16	23.81	38.90
-SK3-12	3/4	19.05	15.74	11/8	28.60	39.90
-SK3-16	1	25.40	22.35	1 3/8	34.92	49.00

 

-SK3 Union Tee (Metric Tube OD x Metric Tube OD x Metric Tube OD)
Ordering Number	A	D	W		E
	mm	mm	in	mm	mm
-SK3-2mm	2	1.70	3/8	9.50	22.30
-SK3-3mm	3	2.40	3/8	9.50	22.30
-SK3-4mm	4	2.40	1/2	12.70	25.40
-SK3-6mm	6	4.80	1/2	12.70	27.00
-SK3-8mm	8	6.40	5/8	16.00	29.90
-SK3-10mm	10	7.90	11/16	17.50	31.50
-SK3-12mm	12	9.50	13/16	20.60	36.00
-SK3-14mm	14	11.10	15/16	23.80	38.80
-SK3-15mm	15	11.90	15/16	23.80	38.80
-SK3-16mm	16	12.70	15/16	23.80	38.80
-SK3-18mm	18	15.10	1 1/8	28.60	39.80
-SK3-20mm	20	15.90	1 3/8	34.90	44.60
-SK3-22mm	22	18.30	1 3/8	34.90	44.60
-SK3-25mm	25	21.80	1 3/8	34.90	49.10

Product Show:
Maxi Metal can supply Various of stainless steel pipe fittings including Elbow, Tee,Cap,Flange,Reducer,Nipple/Connector
, Ball Value, Butterfly valve,Connection Clamp, Union and etc.

 

 

Company Information:

  With wide experience and expertise, CZPT Metal Group is 1 of the leading stainless steel pipe fittings manufacturers and suppliers,  The company through investment steel smelting and forging factory resume stability, a wide range of available resources.Main produce and process stainless steel bar/rod/shaft/profile,stainless steel pipe/tube, stainless steel coil/sheet/plate/strip, stainless steel wire/wire rod/wire rope.Our company supply products from MAXI,TISCO, LISCO, BAOSTEEL, JISCO and so on.We can customize non-standard special stainless steel products with high quality with short time. Our products used to chemical treatment equipments, chemicals tanks, petrochemical equipment and press plates. It is also used in railway coaches, roof drainage products, storm door frames, food machinery and tableware.
    Our company developed international markets more than 25 years, and established long partnership with Germany, South American ,Australia, Saudi Arabia ,Southeast Asia. etc . We will be on the basic of advanced management and service concept to provide high quality products and perfect service for all over the manufacturing enterprise. We welcome customers from all over the world to cooperate with us.

Packing & Delivery:

Maxi metal has its own shipping company to ensure lowest freight,professional service on delivery and Custom Clearance,we arrange good packing like wooden case, waterproof paper to ensure goods in a safty condition during transportation.

Certificate: 

Quality is an integral part of CZPT Metal Business Principles. The quality policy guides us to deliver products and services that exceed the customers’ expectations and meet all the standards. These principles have helped us to get the recognition as a trusted vendor from customers around the world. CZPT Metal Products are trusted and chosen by customers all over the world. This trust is based upon our quality certified and our reputation for consistently delivering high-quality products.
Why Choose us:
 
What you could get from CZPT if we work together?

1. Quality:
We are professional symbol of Chinese Metal industry; so all the supplied metal products from MAXI are quality researched & guaranteed well ones. Quality is our life. No quality, no biz.

2. Price:
Based on mature and rich acknowledge & experience for stainless steel and alloy steel , MAXIMETAL’s supplied price could ensure customer has unique competitiveness in the market. As our aim is long-term biz instead of only profit by 1 or 2 order, we understand only customer win, we could win.

3. Delivery:
MAXI is 1 of TOP 10 manufacturer of stainless steel and alloy products in China, Hold 10000tons raw materials in stock,has its own rolling factory,So enjoy high priority for delivery: Usually within 10-15 from deposit date.

4. Payment:
MAXI supply 30% TT IN ADVANCE + 70% TT WITHIN 7 DAYS OF BL DATE or IRR L/C AT SIGHT for customers. And with cooperation’s growing & mature, better & better payment term will be issued, such as: L/C 30 DAYS, L/C 60 DAYS, L/C 360 DAYS, etc.

5. Service:
From MAXI, what customer could get is not only product, but also complete comprehensive marketting concept & service.

 FAQ:

 

Q1. What are your company’s main products ?

A1: Our main products are stainless steel plate/sheet, coil, round/square pipe, bar, channel,Wire,Wire rod and etc.

 

Q2. How do you control quality ?

A2: Mill Test Certification is supplied with shipment, Third Party Inspection is available. and we also get ISO,SGS Verified.

 

Q3: What is the terms of packing?

A3: generally, we pack our goods in bundles or coils with rods or belts, we could also pack the goods as the customers requirement.

 

Q4:What is your delivery time?

A4: For stocks, we could transport the goods to loading port within 7 days after we received your deposit

For production period, it usually takes about 15 days-30 days after receiving the deposit.

 

Q5. What are the advantages of your company ?

A5: We have many professionals, technical personnel, more competitive prices and best after-dales service than other stainless steel companies.

 

Q6. How many coutries you already exported ?

A6: Exported to more than 50 countries mainly from America, Russia, UK, Kuwait, Egypt, Turkey, Jordan,India,Philippines, Switzerland, South Korea, Vietnam etc.

 

Q7. Can you provide sample ?

A7: We can provide the samll samples in stock for free, as long as you contact us.

Customized samples will take about 5-7days.

Screw Shaft Features Explained

When choosing the screw shaft for your application, you should consider the features of the screws: threads, lead, pitch, helix angle, and more. You may be wondering what these features mean and how they affect the screw’s performance. This article explains the differences between these factors. The following are the features that affect the performance of screws and their properties. You can use these to make an informed decision and purchase the right screw. You can learn more about these features by reading the following articles.

Threads

The major diameter of a screw thread is the larger of the 2 extreme diameters. The major diameter of a screw is also known as the outside diameter. This dimension can’t be directly measured, but can be determined by measuring the distance between adjacent sides of the thread. In addition, the mean area of a screw thread is known as the pitch. The diameter of the thread and pitch line are directly proportional to the overall size of the screw.
The threads are classified by the diameter and pitch. The major diameter of a screw shaft has the largest number of threads; the smaller diameter is called the minor diameter. The thread angle, also known as the helix angle, is measured perpendicular to the axis of the screw. The major diameter is the largest part of the screw; the minor diameter is the lower end of the screw. The thread angle is the half distance between the major and minor diameters. The minor diameter is the outer surface of the screw, while the top surface corresponds to the major diameter.
The pitch is measured at the crest of a thread. In other words, a 16-pitch thread has a diameter of 1 sixteenth of the screw shaft’s diameter. The actual diameter is 0.03125 inches. Moreover, a large number of manufacturers use this measurement to determine the thread pitch. The pitch diameter is a critical factor in successful mating of male and female threads. So, when determining the pitch diameter, you need to check the thread pitch plate of a screw.

Lead

In screw shaft applications, a solid, corrosion-resistant material is an important requirement. Lead screws are a robust choice, which ensure shaft direction accuracy. This material is widely used in lathes and measuring instruments. They have black oxide coatings and are suited for environments where rusting is not acceptable. These screws are also relatively inexpensive. Here are some advantages of lead screws. They are highly durable, cost-effective, and offer high reliability.
A lead screw system may have multiple starts, or threads that run parallel to each other. The lead is the distance the nut travels along the shaft during a single revolution. The smaller the lead, the tighter the thread. The lead can also be expressed as the pitch, which is the distance between adjacent thread crests or troughs. A lead screw has a smaller pitch than a nut, and the smaller the lead, the greater its linear speed.
When choosing lead screws, the critical speed is the maximum number of revolutions per minute. This is determined by the minor diameter of the shaft and its length. The critical speed should never be exceeded or the lead will become distorted or cracked. The recommended operational speed is around 80 percent of the evaluated critical speed. Moreover, the lead screw must be properly aligned to avoid excessive vibrations. In addition, the screw pitch must be within the design tolerance of the shaft.

Pitch

The pitch of a screw shaft can be viewed as the distance between the crest of a thread and the surface where the threads meet. In mathematics, the pitch is equivalent to the length of 1 wavelength. The pitch of a screw shaft also relates to the diameter of the threads. In the following, the pitch of a screw is explained. It is important to note that the pitch of a screw is not a metric measurement. In the following, we will define the 2 terms and discuss how they relate to 1 another.
A screw’s pitch is not the same in all countries. The United Kingdom, Canada, and the United States have standardized screw threads according to the UN system. Therefore, there is a need to specify the pitch of a screw shaft when a screw is being manufactured. The standardization of pitch and diameter has also reduced the cost of screw manufacturing. Nevertheless, screw threads are still expensive. The United Kingdom, Canada, and the United States have introduced a system for the calculation of screw pitch.
The pitch of a lead screw is the same as that of a lead screw. The diameter is 0.25 inches and the circumference is 0.79 inches. When calculating the mechanical advantage of a screw, divide the diameter by its pitch. The larger the pitch, the more threads the screw has, increasing its critical speed and stiffness. The pitch of a screw shaft is also proportional to the number of starts in the shaft.

Helix angle

The helix angle of a screw shaft is the angle formed between the circumference of the cylinder and its helix. Both of these angles must be equal to 90 degrees. The larger the lead angle, the smaller the helix angle. Some reference materials refer to angle B as the helix angle. However, the actual angle is derived from calculating the screw geometry. Read on for more information. Listed below are some of the differences between helix angles and lead angles.
High helix screws have a long lead. This length reduces the number of effective turns of the screw. Because of this, fine pitch screws are usually used for small movements. A typical example is a 16-mm x 5-inch screw. Another example of a fine pitch screw is a 12x2mm screw. It is used for small moves. This type of screw has a lower lead angle than a high-helix screw.
A screw’s helix angle refers to the relative angle of the flight of the helix to the plane of the screw axis. While screw helix angles are not often altered from the standard square pitch, they can have an effect on processing. Changing the helix angle is more common in two-stage screws, special mixing screws, and metering screws. When a screw is designed for this function, it should be able to handle the materials it is made of.

Size

The diameter of a screw is its diameter, measured from the head to the shaft. Screw diameters are standardized by the American Society of Mechanical Engineers. The diameters of screws range from 3/50 inches to 16 inches, and more recently, fractions of an inch have been added. However, shaft diameters may vary depending on the job, so it is important to know the right size for the job. The size chart below shows the common sizes for screws.
Screws are generally referred to by their gauge, which is the major diameter. Screws with a major diameter less than a quarter of an inch are usually labeled as #0 to #14 and larger screws are labeled as sizes in fractions of an inch. There are also decimal equivalents of each screw size. These measurements will help you choose the correct size for your project. The screws with the smaller diameters were not tested.
In the previous section, we described the different shaft sizes and their specifications. These screw sizes are usually indicated by fractions of an inch, followed by a number of threads per inch. For example, a ten-inch screw has a shaft size of 2” with a thread pitch of 1/4″, and it has a diameter of 2 inches. This screw is welded to a two-inch Sch. 40 pipe. Alternatively, it can be welded to a 9-inch O.A.L. pipe.

Shape

Screws come in a wide variety of sizes and shapes, from the size of a quarter to the diameter of a U.S. quarter. Screws’ main function is to hold objects together and to translate torque into linear force. The shape of a screw shaft, if it is round, is the primary characteristic used to define its use. The following chart shows how the screw shaft differs from a quarter:
The shape of a screw shaft is determined by 2 features: its major diameter, or distance from the outer edge of the thread on 1 side to the inner smooth surface of the shaft. These are generally 2 to 16 millimeters in diameter. Screw shafts can have either a fully threaded shank or a half-threaded shank, with the latter providing better stability. Regardless of whether the screw shaft is round or domed, it is important to understand the different characteristics of a screw before attempting to install it into a project.
The screw shaft’s diameter is also important to its application. The ball circle diameter refers to the distance between the center of 2 opposite balls in contact with the grooves. The root diameter, on the other hand, refers to the distance between the bottommost grooves of the screw shaft. These are the 2 main measurements that define the screw’s overall size. Pitch and nominal diameter are important measurements for a screw’s performance in a particular application.

Lubrication

In most cases, lubrication of a screw shaft is accomplished with grease. Grease is made up of mineral or synthetic oil, thickening agent, and additives. The thickening agent can be a variety of different substances, including lithium, bentonite, aluminum, and barium complexes. A common classification for lubricating grease is NLGI Grade. While this may not be necessary when specifying the type of grease to use for a particular application, it is a useful qualitative measure.
When selecting a lubricant for a screw shaft, the operating temperature and the speed of the shaft determine the type of oil to use. Too much oil can result in heat buildup, while too little can lead to excessive wear and friction. The proper lubrication of a screw shaft directly affects the temperature rise of a ball screw, and the life of the assembly. To ensure the proper lubrication, follow the guidelines below.
Ideally, a low lubrication level is appropriate for medium-sized feed stuff factories. High lubrication level is appropriate for larger feed stuff factories. However, in low-speed applications, the lubrication level should be sufficiently high to ensure that the screws run freely. This is the only way to reduce friction and ensure the longest life possible. Lubrication of screw shafts is an important consideration for any screw.